Drills and Drill Bits
Grainger Sq. End Mill Single End Carb 1/2
The 14M684 is a Grainger 4-Ton Bottle Jack manufactured by Torin. It has a lifting range of 11-7/8" to 16-1/4" and a lowered height of just 9". The jack has a steel frame and baseplate and includes an extension screw for adjusting height. Its maximum lifting capacity is 8,000 lbs. The jack's handle is 45 degrees offset for increased leverage and its wide base provides stability under load. This heavy duty hydraulic jack is designed for shop use and farm equipment repair.
Grainger Cor Rad End Mill 1/16 Carb 0.0100 rad
The Corner Radius End Mill by Niagara Cutter is a high-performance end mill designed for milling corners and edges with a radius. It features a corner radius of 0.031 inches and an overall length of 2.5 inches. The end mill has 4 flutes and is made of solid carbide for durability and long tool life. It has a neck relief to provide strength in high load applications. The end mill has a TiAIN coating to resist heat and built-up edge. It can machine a variety of materials including steel, stainless steel, cast iron, aluminum, titanium and nickel alloys. The end mill is center cutting and provides excellent chip control when milling corners and edges.
Grainger Cor Rad End Mill 1/16 Carb 0.0050 rad
The Micro 100 Corner Radius End Mill is a carbide end mill with a corner radius of 0.031 inches. It has a 1/4 inch shank diameter and is available in a length of 2 inches. The end mill has a TiAlN coating and 4 flutes. It is designed for high feed milling in steel, stainless steel, and cast iron. The end mill provides good chip evacuation and can mill small radii.
Grainger Sq. End Mill Single End Carb 6.00mm
The Grainger Approved Square End Mill Single End is a high-speed steel end mill with a square end for milling slots, keyways, and pockets. It has a 1/2" shank diameter, a 1-1/2" overall length, and a 1/2" cutter diameter. The number of flutes is 2. This end mill is uncoated and made in the USA. The primary applications are slotting, side milling, and pocketing in low carbon steels at surface speeds up to 115 SFM when used with rigid setups.
Grainger Ball End Mill Single End 0.40mm Carbide
The Micro 100 Ball End Mill Carbide is a 2-flute ball end mill made of solid carbide with a TiAlN coating. It has a 1/4" shank diameter, 1/2" cutting diameter, and 2" overall length. This 2-flute design provides good chip ejection and finish. The TiAlN coating improves tool life and heat resistance. It can machine steels, stainless steels, cast iron, hardened steels, titanium, and nickel alloys. It has a center cutting design for plunging capability. Recommended speeds are 18,000-22,000 RPM with .001-.004" per tooth feed rates. It is well-suited for complex 3D contouring and profiling with its ball end geometry.
Grainger Sq. End Mill Single End Carb 0.0100
The 14K478 is a 3M Scotch-Brite General Purpose Hand Pad, 6" x 9", Very Fine grade. It features an open web construction and is made of high-quality fibers for cleaning, scouring, and finishing applications. This hand pad has an extra fine grade that can be used for light scrubbing and finishing work. It is 6 inches wide and 9 inches long, suitable for most hand-held scrubbing tasks. The open web design allows debris and dirt to collect inside the pad instead of on the surface. It can be used wet or dry on most surfaces including stainless steel, porcelain, fiberglass and plastics. The Scotch-Brite brand offers consistent high quality.
